Is this compatible with epodex eco epoxy, I need to colour 42kg
Hi david.
Sorry the response is late but yes you can pigment Epoxy but at 10% ratio by weight.
Hi
Is this Satin and powder ? suited for metal.
Hi Jay.
Sorry this is so late but the pigment to be mixed in Topcoat is a paste and not a powder.
Hi
Just bought some of this. There didn’t seem to be any mixing instructions though if you can let me know what they are and any advice on application. Thanks
Keith F
Hello Keith. Gelcoat filler is subjective because under normal condition with polyester resin you would apply 20ml per 1kg. But this product is used in very small quantities (5grm at a time) so a small dribble of catalyst would need to be used.
Hope this helps.
Hi is this plastic spheres or glass?
Hi Daniel. Fillite is like a fine powder but cures really hard. Spheres or glass is West 409.
I have a hollow Glass fibre spoiler- that needs more rigidity, having read up - 2 part high density foam sounds if it would help. But, how much to pour in, would it split the spoiler, do I need a large escape vent hole to ensure no warping ? , thanks DC
Hi Dale.
Yes this needs an escape hole and the calculation is every 1kg mix is 1 x cubic foot.
Can you mix a colour match if I send in a chip of my gelcoat? Closest colour on RAL chart is 5018 turquoise blue but it isn’t that close. Also looking for Scott Bader 337 white
Hi Dean. Please send in a well polished sample at approx 2" and we will get it checked. Scott Bader 337 is a stock item.
I would like to purchase 15 pails (20kg each) of Scott Bader Crystic 1355PA Class 1 Fire Retardant Resin (Inc Catalyst).
Could you please advise the estimated delivery time to Hong Kong and the shipping cost?
Thanks.
Hi Siena. Unfortunately we can not deliver to Hong Kong. We are limited to shipping information unless you can arrange your own internal transport. Regards Paul.
Hi
Is this suitable to re coat an existing fibreglass roof if I sand the old gel coat and what roughly is the coverage per litre.
Thanks
Hi Keith.
First you must remove all traces of topcoat as this still contains a wax and may pre release. It is advised to remove all back to the laminate and acetone wipe and then re-apply.
How big is a 1kg tin is it equivalent to 1ltr
Yes, it is roughly equivalent to 1L. Pigments vary slightly as certain colours weigh more than others but it is made in a 1L tin.
I want to use this filler to fill some screw holes and gouges up to 5mm deep on a vertical surface but it's too runny. Is there a way of thickening it?
Hi Kim.
I would first fill the holes with a strong body filler leaving about 2mm the replace the gelcoat. Gelcoat, if applied too thick is prone to cracking.
Is it possible to colour Isopon p38 car filler with a portion of ral3012 to stain it?
Hi Peter.
Isopon can be coloured using our standard pigments. 10-15% should be fine.
Is this correct product to repair chips in a Humber Destroyer hull?
Thanks
Nick
Hi Nick.
Your best product will be Gelcoat filler with the colour you have chosen. Put the colour number in the special instructions at the end.
Can I use on fiberglass boat repair
Hi Dan.
A gelcoat filler ( white) is the best option if they are small gelcoat repairs.
how many ml is 1.1kg or what is the square foot coverage?
Thanks
Hi Martin. 1.1kg will cover approx 2Mtr2
What is the coverage of 20kg of top coat and is there a data sheet available
Hi Mike. This is approx 500-600grm per mtr 2. Data sheet is available.
How much of the expanding foam fluids would be required to fill an industrial bulk chemical cube ,1 cubic metre.
Edd Connor
Hi Edd.
1 x kg Pt1 and 1 x kg Pt 2 will cover 2 cubic feet.
Starchem Bridger
What is the catalyst to paste ratio please
Hi max. The ratio is 2%. = 25grm resin to 1cm cat bpo
Hi
I purchased this product but it has come with no instructions for use.
Could you tell me please, the mixing ratio for this
Regards
Hi Peter.
The only calculation you will need is every 1kg of resin you need 20ml of catalyst. This is 2% catalyst ratio. The hotter it is the less catalyst is required. Average is 16-21% heat for the material to cure.
Hope this helps.
Are these pigments in powder form? Can I use them to color waxes? Thank you
Hi Adrian.
These pigments are in paste form so only can be mixed in Polyester resin or Epoxy.
what is grade / size of the grit
Need some thing coarse for painted concrete walkways.
Hi Andy,
The grade listed on the data sheet is - FEPA F and P grit in macro range 8 to 220 and micro 240 to 1200
Let us know if you have any other questions.
Thank you
Can I use this paint on my soffits, fascias and barge boards?
Hi Adrian. Unfortunately not as this will peel off plastic.
Hi I have received my order of Crestomer 1152PA I have opened the tin and it is a thick wall paper paste consistency. Is this correct? Also on the description it says two part. Do I have to buy part 2 separately? Of so what is it called?
Thanks Mark
Hi Mark.
Yes this material is like a body filler consistency and requires the addition of a catalyst to set it off. This product is probably the most adhesive Crestomer on the market and can be applied up to 30mm thick.
Hope this helps.
I'm willing to buy the M1-30 but coudnt see the hardener tube... Does it follow or I will have to purchase it separately? Another thing is the gun, please show me a suitable one for the 490ml M1-30... Thanks in advance!
Hi Arnaldo.
This producy has the catalyst piggy backing the main tube like a space rocket. It requires a gun with two pistons to be able to apply both materials at the correct percentage.
What is the coverage ratio please, I can't find it 1sq meter equals how much topcoat, thanks darren
Hi darren.
The approximate quantity is 500-600grm per square metre.
Hi. Can this product be used as boat transom plywood replacement (Liquid transom)? Thank you.
Hi Dragos.
Yes this product ( Isothalic Resin) can be used on a transom. It is overkill but be assured of its rigitity. Perfect.
Hi. Can this product be used for filling boat transom replacing plywood? Thank you.
Hi Dragos.
No this product can not have a thickness of cure more than 1cm. This will just crack under the exotherm.
Hello.
We have a steep access ramp which regularly gets wet. It's 4ft wide & 12ft long & surface is metal chequer plate.
Im looking for the gripyist topcoat I can apply that'll form a hard-wearing and nonslip covering?
Thanks in advance.
Hi Marcus.
We will probably have to suggest Restec system as you need to apply a primer for the metal surface and they a Restec system with a gravel material and balcony sealer to make it rigid. You will lose the metal look unfortunately.
Is this suitable to bond in replacement stringers and to be fibreglassed in place?
Hi Valerie.
Yes this can be used but be careful as it has a very quick cure time (8 mins) 1196PA is a better product for stringers.
G275 External Roof Trim.
What thickness is this please.
and can it be painted?
Looking to use this as a flat roof edge trim.
Hi Steve. The thicknes is 450grm (1mm thick) and it can be painted.
Hello,
Can I add pigment to this? It needs to be as close to navy blue (dark blue as possible) doesnt have to be perfect
what do you reccomend?
MAny thanks
ROy
Hi Roy.
Unfortunately this product is already white and would take a lot of pigment to get it to your desired colour. Also this would effect the cure rate and properties of the product. Please look at standard gelcoat filler to your desired Ral colour on our website.
I would recommend this course of action.
Hello, Would this adhesive be useful in an instance where we are using htem between Carbon fiber rod placed inside a steel rode. There is a chance that this assembly could be subjected to a high loads during its tensile testing procedure,
Could you please clear this up for me?
Thanks loads!
Hi Sam.
This product is very good under extreme load so yes i would recommend this. Also look at the data sheet for 1186PA Crestomer. A cheaper version but very effective.
Sorry this has taken so long to respond.
Hi can you mix Ral white 10954 beige white
kind regards
Russell
Hi,
Thank you for your question, we can mix to classic RAL colours which are usually 4 numbers.
If there is any confusion, you can always give us a call and we're more than happy to help.
Thank you,
FSL
Hi, is this suitable for use under the water line of a GRP boat if it is getting primed and antifouled or do I need a waterproof marine filler?
Hi Trev.
Yes this material will be fine under the waterline.
Hello, I am interested in you carborundum grit and am looking for a particularly coarse grade. Would you please reply to me with the diameter (mm) of the particle grade that you.
Thank you,
Miriana
Hi Mirana.
Our product is 8-220 mesh, 240-12200 microns. Hope this helps.
Can you please provide the dimensions of this product and the thickness of it.
Thank you
Hi Ed.
So sorry this email has escaped us. The information you require is
3mtr long
450grm grade mat
200mm wide.
Hope this helps.
Can you provide the dimensions of this product and thickness please.
H, L, W of the fillet
Hi Ed. I believe we may have answered this one already but here goes.
3mtr Long
450grm CSM used
200mm wide
Hi
I manufacture mdf kitchen doors and I’m wondering if I could use your white polyester like a primer to spray on router edges and fronts to fill and create a smooth surface for polyurethane paint?
Regards David Collier
Hi David. This product can be sprayed with the extra addition of styrene. The only unfortunate issue is it is not very good at filling gaps or holes because you need the viscosity to spray and it may run on vertical surfaces. Unfortunately you may need to do a trial of a panel and test. Hope this helps and sorry it's taken so long to resond. FSL Team
Hello, I hope you are well. We have hardwood front doors which have been stained with Ronseal Satin Deep Mahogany and we are looking for a matching paint for the garage door which is fibreglass. Will this paint (RAL 8012 Red Brown) be suitable? Also will the colour match? Thank you.
Hi Gursewak. Unfortunately our colours are pigmentations that you apply into polyester or Epoxy resin. I'm not sure if this is ok for your application. You may need to do a test if this is to succeed.
Can you advise on the average coverage in M2 please?
Hi Clive. Sorry this has taken so long to respond. The approx coverage is 500-600grm per mtr Hope this helps.
Hi which catalyst do I need for your gel coat
Hello,
Thank you for your question, for gelcoat and topcoats you would need to use MEKP which is a standard catalyst.
https://www.fslplymouth.co.uk/catalyst/grp-catalyst-hardener-mekp-organic-peroxide/
*Please note that the product you have questioned this on is a pigment*
Thank you!
How much catalyst do I use in ratio to filler.
Bought a small tin of this
Also will the catalyst added change the colour of the filler in tin
Hi Del.
As you can appreciate, using small amounts is very difficult to measure catalyst ratio's. The rule of thumb is 1 x good measure (1cm) of filler to half a cap full of cat. You will have to gauge the timings as every day is has a variant in the temperature.
Do your grp refresh top coats require a catalyst thanks
Hi, thank you for your question. Yes, this product will require catalyst. It uses our standard MEKP (https://www.fslplymouth.co.uk/catalyst/grp-catalyst-hardener-mekp-organic-peroxide/)
